Дастури корбар барои дастгоҳҳои Ajax мувофиқ
Навсозии 14 марти соли 2025
Case is the casing designed to install one or more compatible Ajax devices. The complete set includes the tamper Шӯрои барои ҳифзи дастгоҳҳо аз sabotage. Case has fasteners to fix the cables and channels for convenient cable organization. The casing is intended for indoor use only.
Case is produced in several versions. Each model has a different number of slots depending on the device combination:
- Case A (106) — one Ajax device;
- Case B (175) — up to two Ajax devices;
- Case C (260) — one Ajax device and 7 Ah battery;
- Case D (430) — up to eight devices and two 18 Ah batteries.
Case харед
Кадом парвандаро интихоб кардан
Унсурҳои функсионалӣ
Парвандаи А (106) Парвандаи В (175) Парвандаи C (260) Парвандаи D (430)
- Holding screws to secure the casing lid. Can be unscrewed with abundled hex key (Ø 4 mm).
- Bubble level to check the inclination angle of the mount during installation.
- Истгоҳҳо барои муҳофизат кардани дастгоҳ ҳангоми пармакунӣ.
- Дар тamper Шӯрои бо сим барои пайваст кардани дастгоҳи Ajax.
- Лампаҳо барои пайваст кардани дастгоҳ.
- Perforated part of the casing. Do not break it off. This part is necessary for tamper triggering in case of any attempt to detach thecasing from the surface.
- Holes to attach the casing to the surface.
- Perforated part to run the wires.
- Fasteners to fi x the cables with ties.
- Recesses to drill the holes conveniently.
Дастгоҳҳои мувофиқ
The number of devices installed into Case depends on the dimensions ofthe casing and its confi guration.
Ҷадвали мутобиқат
Case A (106)
Парвандаи В (175)
Case C (260)
Парвандаи Д
Хусусиятҳои асосӣ
Case has latches for attaching devices without tools. Slide the latch toremove the device.
Дастгоҳ дар ду мавқеъ ҷойгир карда шудааст. Шумо метавонед онро 180 ° гардонед.
Case has fasteners to fi x the cables with ties and channels for convenientcable routing. The casing has perforated parts to run the cables throughthe back side. There are recesses to place the drill conveniently (in caseyou need to drill holes and run the cables along the side, bottom, or top).During drilling, the tool rests on plastic stoppers, ensuring the installed devices remain protected.
Сарпӯши парвандаи A (106) ё парвандаи B (175) ҳангоми насб 180° гардиш кардан мумкин аст.
Case C (260) and Case D (430) have battery holders at the bottom of thecasing to prevent accidental dislodgement. The holding stripe for securingthe battery is included with Case D (430).
Case D (430) has sixteen slots for plastic holders for Fibra modulesinstallation. Holders are available in two versions:
- Module Holder (type A) for Superior LineSplit Fibra, Superior LineProtect Fibra, Superior MultiRelay Fibra attachment;
- Module Holder (type B) — for Superior Hub Hybrid (4G) (without casing) and Superior MultiTransmitter Fibra (without casinж).
Чор ҳастанд Module Holder (type A) in the complete set. Additional holders and Module Holder (type B) алохида фурухта мешаванд.
Superior LineSupply Fibra барои насб дорандагони талаб намекунад.
Интихоби макони насб
It is advisable to choose an installation site where Case is hidden fromprying eyes — for example, in the pantry. This will help reduce thelikelihood of the system sabotage. Note that the device is intended forindoor installation only.
The Case installation site must comply with the recommendations formounting the devices installed in the casing.
Follow these recommendations when designing the Ajax system projectfor an object. The system should be designed and installed byprofessionals. The list of authorized Ajax partners is дар ин ҷо дастрас аст
Парвандаи онро насб кардан мумкин нест
вasing can be damaged if you install it:
- Дар берун.
- Inside premises with temperature and humidity values that do not correspond to the operating parameters
Омодагӣ ба насб кардани дастгоҳҳо дар Case
Кадом парвандаро интихоб кардан
Use Case configurator to get the most optimal placement of your Fibra devices in the casing.
Тартиби кабелӣ
When preparing to cable routing, check the electrical and fi re safety regulations in your region. Strictly follow these standards and regulations.Tips for cable arrangement are available in this article
Масири кабелӣ
We recommend you read the Selecting the installation site section carefully before installation. Avoid deviations from the system project.Violating the basic installation rules and the recommendations of this manual may lead to incorrect operation and loss of connection with devices installed into Case.
Кабелро чӣ гуна бояд кашид
Омода кардани кабелҳо барои пайвастшавӣ
Remove the insulating layer and strip the cable with a special insulationstripper. The ends of the wires inserted into the device terminals must betinned or crimped with a sleeve. This ensures a reliable connection andprotects the conductor from oxidation.
Чӣ тавр тайёр кардани кабел
Насбкунӣ
Before installation, ensure that you have selected the optimal location forthe casing and that it complies with the requirements of this manual.
Case A (106)
Парвандаи В (175)
Case C (260)
Case D ( 430)
Барои насб кардани Case:
- Prepare cable holes in advance: drill the holes in the bottom or side ofthe casing or break out the perforated part on the back of Case. Werecommend using a hole saw for plastic Ø16 mm or Ø20 mm.
Insert the pipe, corrugated pipe or conduit into the holes in the casing.
2. Route the cables and lead them through the pre-prepared holes.Secure Case on the vertical or horizontal surface at the selected installation site with the bundled screws using all fixation points. One of them is in the perforated part above the tamper — it is required fortamper triggering if someone tries to detach the casing.
3. Secure the device in the casing. Connect the cables to the corresponding terminals. Fix the cables with ties using fasteners.
4. t-ро пайваст кунедamper Шӯрои ба пайвасткунаки дастгоҳ мувофиқ.
5. Place the lid on the casing and fasten it with the bundled screws.
6. Check the state of the lid in the Ajax app. If the app shows the Front lid open state, check the tightness of Case.
Нигоҳдорӣ
Дастгоҳ нигоҳдорӣ талаб намекунад.
Мушаххасоти техникӣ
Technical specifications for Case A (106)
Technical specifications for Case B (175)
Technical specifications for Case C (260)
Technical specifications for Case D (430)
Мутобиқати стандартҳо
Кафолат
Кафолат барои маҳсулоти Ҷамъияти дорои масъулияти маҳдуди "Ajax Systems Manufacturing" барои 2 сол пас аз харид эътибор дорад.
Агар дастгоҳ дуруст кор накунад, аввал бо дастгирии техникии Ajax тамос гиред. Дар аксари мавридҳо, масъалаҳои техникӣ метавонанд ба таври фосилавӣ ҳал карда шаванд.
Ӯҳдадориҳои кафолат
Шартномаи корбар
Бо дастгирии техникӣ тамос гиред:
- почтаи электронӣ
- Telegram
Истеҳсолкардаи ҶДММ “AS Manufacturing”
Ба бюллетен дар бораи ҳаёти бехатар обуна шавед. Спам нест
Муфассалтар дар бораи ин дастур хонед ва PDF-ро зеркашӣ кунед:
Ҳуҷҷатҳо / Сарчашмаҳо
 |
Дастгоҳҳои Ajax мувофиқи парвандаи AJAX [pdf] Дастури корбар Парвандаи A 106, Парвандаи B 175, Парвандаи C 260, Парвандаи D 430, Дастгоҳҳои мувофиқи Ajax, парванда, Дастгоҳҳои мувофиқи Ajax, Дастгоҳҳои Ajax, Дастгоҳҳо |