D149H181 Ed.08

AKO-D14918

Дар AKO-D14918 programming key allows you to quickly and easily copy configured settings from one controller to another with the same functionality

Огоҳӣ

-Using the equipment without following the manufacturer’s instructions may affect the device’s safety requirements.
-The unit must be used in a location protected from vibrations, water and corrosive gases, where the ambient temperature does not exceed that shown in the technical data.
-Connecting this key to unsupported devices (see table) can cause serious damage to both pieces of equipment.
-In equipment with active communication, log out of communications software or disconnect the cable before connecting the programming key. The communication controller’s address must be 1.

Тавсифи

1. LED COM
2. КАЛИДИ САБТ
3. EXTERNAL POWER CONNECTOR
4. READ KEY
5. LED фаъол аст
6. CONNECTOR CABLE

Мутобиқати

Refer to the instruction manual of your equipment on its compatibility with the AKO-D14918 калиди барномасозӣ.

Connecting incompatible devices can permanently damage the key.

Ноқилҳо

1. МУҲИМ: Pay attention to the orientation of the connector.
2. АКО-80018 
   (Ихтиёрӣ)
3. AKO-D14918

Таъмини нерӯ

-If the controller is in operation (on-site programming), the key does not require an external power supply (it is powered via the connecting cable).
-If the controller is NOT powered (workshop programming), the key requires a 12Vdc/500 mA external power supply (АКО-80018 or equivalent).

Амалиёт

МУҲИМ: After connecting the key to the equipment wait for 5 seconds before starting the reading or writing process.

RECORD key

Write the data contained in the key memory to the controller.
Keep the key pressed until the COM led starts flashing quickly.
When recording is complete the controller will reset.

READ key

It reads the data from the controller and stores them in the programming key.
Keep the key pressed until the COM led starts flashing quickly.
When recording is complete the controller will reset.

LED фаъол аст

Steady or flashing: Indicates that the key is connected to the controller.

LED COM

устувор: Indicates an error in the transmission/reception of data
Дурахшиши зуд: Indicates transmission/reception of data in progress. At the end of the transmission LED COM хомӯш мешавад.
Дурахши суст: Indicates compatibility error- the data contained in the memory of the key is not compatible with the model of controller connected. Data can only be read from the controller to the key.

ШАРҲ: To restart after a transmission or compatibility error, turn off the power supply or disconnect the controller connector cable.

МУҲИМ: Ҳеҷ гоҳ disconnect the programming key during data transmission.

Мушаххасоти техникӣ

Length of cable from programming key to controller . . . . . . . . . . . . . 300 mm
Таҳвили ҷилдtage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Vdc nominal
Supply current . . . . . . . . . . . . . . . . . . . . . . . . . . . . AKO-80018 / 500 mA máx.
Мушаххасоти экологӣ:
Ambient working temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . 0ºC to 50ºC
Storage temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -30ºC to 70ºC

AKO ELECTROMECÁNICA, SA
Ав. Рокетес, 30-38 | 08812 Сант Пере де Рибес | Барселона | Испания

35D149181 REV.07 2025

Мо ҳуқуқ дорем, ки маводҳоеро, ки дар Лавҳаҳои техникии мо тавсиф шудаанд, каме фарқ кунанд.
Маълумоти навшуда дар мо дастрас аст webсайт.

Ҳуҷҷатҳо / Сарчашмаҳо

AKO D14918 Programming Key [pdf] Дастури дастур AKO-D14918, AKO-80018, D14918 Programming Key, Programming Key, Key

Иқтибосҳо

• Дастури корбар