1. Муқаддима
This manual provides detailed instructions for the proper installation, operation, and maintenance of your Lanzar VIBE211 Vibe 360 Watt 2 Channel Mosfet Ampбаландкунанда. Лутфан пеш аз кӯшиши насб кардан ё истифода бурдани ин дастурро бодиққат хонед amplifier to ensure optimal performance and safety.
2. Маълумот оид ба бехатарӣ
Ҳангоми насб ва истифода ҳамеша чораҳои бехатарии зеринро риоя кунед:
- Disconnect the vehicle's negative battery terminal before any wiring connections are made.
- Боварӣ ҳосил кунед, ки ҳама ноқилҳо дуруст ба роҳ монда шудаанд ва барои пешгирӣ кардани осеб ё ноқилҳои кӯтоҳ таъмин карда шудаанд.
- Барои пайвастҳои барқ ва заминӣ, ки дар бахши насб нишон дода шудаанд, аз симҳои андозагирии мувофиқ истифода баред.
- Монтед ampлифтро дар ҷойе, ки вентилятсияи мувофиқро фароҳам меорад ва аз намӣ ва гармии аз ҳад зиёд муҳофизат мекунад, бехатар нигоҳ доред.
- -ро истифода набаред amplifier if it is damaged or malfunctioning. Refer to the troubleshooting section or seek professional assistance.
3. Маҳсулот ба охир расидview
The Lanzar VIBE211 is a 2-channel Mosfet amplifier designed for car audio systems. It features a bridgeable design, allowing for flexible configuration, and incorporates a regulated Mosfet power supply for stable performance. Key features include variable high/low pass crossover controls and a remote subwoofer bass control.
Як кунҷӣ view of the silver Lanzar VIBE211 Vibe 360 Watt 2 Channel Mosfet Ampбаландкунанда, намоишasing its finned heatsink design, RCA inputs, and control panel. The amplifier features text indicating 'bridgeable 2 channel amplifier', 'vibe 211', 'Lanzar vibe', '360 watts', 'high/low pass crossover', and 'regulated mosfet power supply'. A small, separate remote bass level control unit is visible in the foreground.
4. Танзим ва насб
4.1 Ҷойгиркунии Ampзиндатар
Choose a secure mounting location that provides adequate air circulation around the amplifier's heatsink. Avoid mounting in direct sunlight or areas prone to moisture. Use the provided mounting hardware to secure the amplifier firmly to a solid surface.
4.2 Пайвастҳои ноқилӣ
Ensure all connections are tight and properly insulated to prevent short circuits.
- Power (B+): Connect a heavy-gauge wire (e.g., 8 AWG or larger) directly from the positive terminal of the vehicle's battery to the amplifier's B+ terminal. Install an appropriate fuse (15A) within 18 inches of the battery.
- Замин (GND): Connect a heavy-gauge wire of the same size as the power wire from the amplifier's GND terminal to a clean, unpainted metal surface of the vehicle chassis. Ensure a good electrical connection.
- Дурдаст (REM): Connect a smaller gauge wire (e.g., 18 AWG) from the ampтерминали REM-и лифт ба баромади дурдасти дастгоҳи саратон. Ин сим гардиш мекунад ampлифтро бо стерео худ фурӯзон ва хомӯш кунед.
- Вурудоти RCA: Connect the RCA audio cables from your head unit's pre-amp баромадҳо ба amplifier's Gold RCA Inputs. The amplifier includes Line Outs for Left and Right Channels for daisy-chaining to other ampосебдидагон.
- Натиҷаҳои баландгӯяк: Connect your speakers to the amplifier's speaker terminals. Observe correct polarity (+ to + and - to -). The amplifier is 2 Ohm stereo stable and bridgeable at 4 Ohms.
- Remote Subwoofer Bass Control: Connect the remote bass control unit to the designated port on the amplifier. Mount the control unit in an accessible location for easy adjustment.
5. Дастурҳои истифодабарӣ
5.1 Фаъолсозии ибтидоӣ
After all connections are made, reconnect the vehicle's negative battery terminal. Turn on your head unit. The amplifier features Soft Turn On/Off circuitry to prevent pops and clicks. Power Protection LED Indicators will illuminate to show operational status.
5.2 Adjusting Input Level Controls
Дар amplifier has Variable Input Level Controls. Start with the amplifier's input level set to minimum. Play a familiar piece of music through your head unit at about 75% of its maximum volume. Slowly increase the amplifier's input level until you hear slight distortion, then back it off slightly. This ensures the amplifier receives an optimal signal without clipping.
5.3 Танзимоти кроссовер
Дар amplifier features Variable High Low Pass Crossover Controls. These allow you to filter specific frequencies to your speakers or subwoofers.
- Филтри гузариш баланд (HPF): Used for full-range speakers to prevent low frequencies from reaching them, improving clarity.
- Филтрҳои пасти гузариш (LPF): Used for subwoofers to allow only low frequencies to pass, enhancing bass response.
Adjust these controls to match the frequency response characteristics of your speakers and subwoofers.
5.4 Bass Boost Circuit
The built-in Bass Boost Circuit allows for an increase in bass output at specific frequencies. Use this feature sparingly and adjust to your preference, avoiding excessive boosting that could lead to distortion or speaker damage.
5.5 Фаъолияти режими пулакӣ
Дар amplifier can be bridged at 4 Ohms to combine the power of both channels into a single, higher-power output, typically for driving a subwoofer. Refer to the wiring diagram for specific instructions on bridging the ampлифер.
6. Нигоҳдорӣ
The Lanzar VIBE211 amplifier requires minimal maintenance. Periodically inspect the wiring connections for tightness and corrosion. Keep the amplifier's heatsink clean and free of dust or debris to ensure proper cooling. Use a soft, dry cloth for cleaning the exterior.
7. Баррасии мушкилот
Агар шумо бо мушкилоти худ дучор шавед amplifier, пеш аз ҷустуҷӯи хидмати касбӣ ба ҷадвали зерин муроҷиат кунед:
| Мушкилот | Сабаби эҳтимолӣ | Ҳалли |
|---|---|---|
| Не қудрат / Не садо | Blown fuse; Loose power/ground/remote wire; Faulty head unit. | Check and replace fuse; Verify all power, ground, and remote connections; Test head unit functionality. |
| Овози таҳрифшуда | Input level too high; Speaker impedance too low; Damaged speakers. | Adjust input level; Verify speaker impedance (2 Ohm stereo stable, 4 Ohm bridged); Inspect speakers for damage. |
| AmpЛифт ба ҳолати муҳофизатӣ мегузарад | Overheating; Short circuit in speaker wiring; Low voltage. | Ensure adequate ventilation; Check speaker wires for shorts; Verify battery voltage and charging system. |
| Басс аз сабвуфер нест | LPF not enabled or set too high; Phase issue; Remote bass control set to minimum. | Adjust LPF setting; Check subwoofer phase; Increase remote bass control level. |
8. Мушаххасоти
Technical specifications for the Lanzar VIBE211 ampумр:
- Power Output (RMS @ 4 Ohms): 2 x 90 Ватт
- Power Output (Max @ 4 Ohms): 2 x 180 Ватт
- Power Output (Max Bridged @ 4 Ohms): 1 x 360 Ватт
- Power Output (RMS @ 2 Ohms): 2 x 150 Ватт
- AmpНавъи умр: 2 Channel Mosfet
- Ҷавоби басомад: 15 Hz - 35 kHz
- Таносуби сигнал ба садо (S/N): 90 дБ
- Рейтинги муҳофиз: 15А
- Андозаҳо (W x H x L): 10.25 дюйм x 2 дюйм x 8 дюйм
- Назорати сатҳи вуруд: Тағйирёбанда
- Назорати кроссовер: Variable High/Low Pass
- Субот: 2 Ohm Stereo Stable, Bridgeable at 4 Ohms
- Схемаи муҳофизатӣ: Advanced Power Protection LED Indicators
- Хусусиятҳои иловагӣ: Remote Subwoofer Bass Control, Electronic Crossover Network, Bass Boost Circuit, Soft Turn On/Off
9. Кафолат ва дастгирӣ
9.1 Маълумот дар бораи кафолат
The Lanzar VIBE211 ampлифофа бо а меояд 1-СОЛ limited warranty from the date of purchase. This warranty covers defects in materials and workmanship under normal use. Please retain your proof of purchase for warranty claims. The warranty does not cover damage caused by improper installation, accident, misuse, abuse, negligence, or unauthorized modification.
9.2 Дастгирии муштариён
For technical assistance, troubleshooting beyond this manual, or warranty service, please contact Lanzar customer support. Refer to the official Lanzar webсайт ё банду маҳсулот барои маълумоти тамос ҷорӣ.
