Phocos CIS10 IP68 10Amp Дастури истифодабарии назорати барқи офтобӣ

1. Муқаддима

This manual provides essential instructions for the safe and efficient operation of your Phocos CIS10 IP68 10Amp Solar Charge Controller. The CIS10 is designed for off-grid solar light systems and battery charging, featuring automatic 12V/24VDC system voltage detection and a robust IP68 waterproof design. Please read this manual thoroughly before installation and use.

2. Маълумот оид ба бехатарӣ

Дастурҳои муҳими бехатарӣ:

• Always connect the battery to the charge controller first, then the solar panel, and finally the load. Disconnect in the reverse order.
• Ensure all connections are tight and secure to prevent excessive voltage drop and loose connections.
• Install the controller in a well-ventilated area, away from flammable gases.
• Контроллерро худатон қисм-қисм ҷудо накунед ё кӯшиш накунед, ки онро таъмир кунед. Барои хизматрасонӣ бо мутахассисони соҳибихтисос тамос гиред.
• Wear appropriate personal protective equipment (PPE) when working with batteries and solar panels.
• The controller is IP68 rated for water and dust ingress, but avoid submerging it for extended periods or exposing it to high-pressure water jets.

3. Хусусиятҳои маҳсулот

The Phocos CIS10 Solar Charge Controller offers the following key features:

• Тарҳрезии обногузар IP68: Suitable for outdoor use, resistant to water spray, rain, and condensation.
• Ҷилди автоматӣtage Муайянкунӣ: Системаи 12V ё 24V DC -ро ба таври худкор муайян мекунадtages.
• 5-Сtage PWM Technology: Provides Soft Start, Bulk, Absorption, Float, and Equalization charging stages for optimal battery health and system performance.
• Мутобиқати васеи батарея: Works with LifePo4, LTO, GEL, AGM, Lead-Acid, Calcium, and EFB batteries.
• Хусусиятҳои муҳофизати бисёрҷониба: Built-in protection against over-temperature, over-voltage, over-current, over-charging, over-discharging, overload, and short circuits.
• Compact and Thin Design: Maximizes solar power utilization with minimal self-power consumption.

4. Танзим ва насб

Follow these steps for proper installation of your Phocos CIS10 controller:

1. Монтаж: Choose a suitable location for mounting the controller. Although IP68 rated, mounting in a shaded or protected area can extend its lifespan. Ensure adequate space for cable connections.
2. Пайвастшавӣ ба батарея: Connect the battery cables to the controller's battery terminals first. Ensure correct polarity (positive to positive, negative to negative). The controller will automatically detect the system voltagд (12V ё 24V).
   

   Image 4.1: Phocos CIS10 controller showing battery, solar panel, and load connection points, along with LED indicators for status.

3. Пайвастшавӣ ба панели офтобӣ: Connect the solar panel cables to the controller's solar panel terminals. Observe correct polarity. The controller will begin charging the battery.
4. Пайвасти боркунӣ (ихтиёрӣ): If using the controller for a DC load (e.g., solar light), connect the load cables to the controller's load terminals. Ensure correct polarity.
5. Тасдиқи пайвастҳо: Double-check all connections for tightness and correct polarity before powering on the system.

The controller's compact design and integrated wiring simplify installation. Its IP68 rating ensures durability in various outdoor conditions.

Image 4.2: The Phocos CIS10 controller demonstrating its compact size with a ruler and highlighting its IP68 waterproof capability.

5. Дастурҳои истифодабарӣ

The Phocos CIS10 operates automatically once connected. It utilizes advanced 5-stage Pulse Width Modulation (PWM) charging technology to optimize battery charging and extend battery life.

5.1. Пур кардани Сtages

• Оғози нарм: Gradually increases current to the battery.
• Нархи яклухт: Delivers maximum current to rapidly charge the battery to approximately 80% capacity.
• Пардохти азхудкунӣ: Charges the battery at a constant voltage to bring it to 100% capacity.
• Нархи шиновар: Maintains the battery at a full charge by providing a small, constant voltage.
• Баробаркунӣ: Automatically performs equalization every 28 days for calcium/EFB batteries to prevent sulfation and ensure cell balance.

5.2. Work Mode (Optional)

The CIS10 controller supports configurable work modes, such as time control and light control, which can be set using an optional external unit like the CIS-CU (sold separately). This allows for customized operation of connected loads, such as solar lights.

6. Нигоҳдорӣ

The Phocos CIS10 is designed for minimal maintenance due to its robust IP68 rating and epoxy-encapsulated PCB. However, periodic checks are recommended:

• Санҷиши визуалӣ: Ба таври даврӣ контроллер ва ҳамаи пайвастҳоро аз рӯи аломатҳои осеб, зангзанӣ ё суст шудани симҳо тафтиш кунед.
• Тозакунӣ: If necessary, gently clean the exterior of the controller with a damp матоъ. Моддаҳои кимиёвии сахт ё маводи абразивиро истифода набаред.
• Саломатии батарея: Monitor your battery's performance. The controller's equalization feature helps maintain battery health for compatible types.

7. Баррасии мушкилот

The CIS10 controller includes multiple built-in protections to prevent damage. If you encounter issues, consider the following:

• No Charging/Load Output:
  • Ҳамаи пайвастҳои симро аз рӯи маҳкамӣ ва қутби дуруст тафтиш кунед.
  • Боварӣ ҳосил кунед, ки панели офтобӣ нури офтобии мувофиқро мегирад.
  • Ҳаҷми батареяро тасдиқ кунедtage is within the operating range (12V/24V).
  • Check for any blown fuses in the system (if applicable).
• Муҳофизати аз ҳад зиёд: If the controller becomes excessively hot, it may temporarily reduce or stop charging/output. Ensure it's not installed in an area with poor ventilation or direct, intense heat.
• Беш аз ҷилдtagд/Зоҳи ҷилдtage Муҳофизат: The controller will protect the battery from overcharging or deep discharge. If the battery voltage is too low, the load may be disconnected.
• Short Circuit/Overload Protection: If a short circuit or overload occurs on the load or solar input, the controller will temporarily shut down to protect itself and the system. Remove the fault and the controller should resume normal operation.

If problems persist, refer to the detailed specifications or contact Phocos customer support.

8. Мушаххасоти

Detailed technical specifications for the Phocos CIS10 Solar Charge Controller:

9. Кафолат ва дастгирӣ

Phocos is a German brand known for quality assurance in solar power products. For warranty information, technical support, or service inquiries, please contact your authorized Phocos dealer or visit the official Phocos webсайт. Квитансияи хариди худро барои даъвоҳои кафолат нигоҳ доред.

For additional resources and product updates, you may visit the Phocos official webсайт.