Муқаддима
Thank you for choosing the Stetsom Vulcan 9K EQ - 1 Ohm 9000W RMS Full Range High Power Ampбаландкунанда. Ин дастур маълумоти заруриро барои насб, истифода ва нигоҳдории дурусти дастгоҳи худ пешкаш мекунад ampбаландкунанда. Лутфан пеш аз истифода бурдани маҳсулот ин дастурро бодиққат хонед, то иҷрои беҳтарин ва бехатариро таъмин кунед.
Маълумоти муҳим оид ба бехатарӣ
- Always disconnect the vehicle's battery before making any electrical connections.
- Барои пешгирӣ кардани хатарҳои барқ ба заминкании дурустро таъмин кунед.
- насб кунед ampлифт дар ҷои хуб вентилятсияшуда барои пешгирии гармии аз ҳад зиёд.
- Use appropriate gauge wiring for power and speaker connections as specified in this manual.
- Аз фош кардан худдорӣ намоед ampбардоред ба намӣ ё ҳарорати аз ҳад зиёд.
- Кушодан ё таъмир накунед amplifier yourself. Refer all servicing to qualified personnel.
Маҳсулот ба охир расидview
The Stetsom Vulcan 9K EQ is a high-power, full-range digital amplifier designed for automotive audio systems. It features a robust design and advanced equalization capabilities to deliver powerful and clear sound reproduction.
Хусусиятҳои асосӣ:
- 9000W RMS power output at 1 Ohm (12.6V)
- Full Range frequency response (10Hz to 15KHz)
- Built-in 3-band equalizer (Bass, Mid Bass, Mid High)
- Over Clip +15% Power indicator
- Protection circuits for safe operation
Идентификатсияи компонент:
Дар amplifier features power, protection, and clip indicators on the front panel. The input and output terminals are located on the side for easy access during installation.
Насб ва насб
1. Пайвастҳои барқ:
- Сими барқӣ (B+): Connect a heavy-gauge power cable directly from the positive terminal of the vehicle's battery to the B+ terminal on the amplifier. An inline fuse or circuit breaker (not included) must be installed within 18 inches (45 cm) of the battery.
- Сими заминӣ (GND): Сими заминии ғафси калибрро аз терминали GND дар дастгоҳ пайваст кунед amplifier to a clean, unpainted metal surface of the vehicle chassis. Ensure a solid, low-resistance connection.
- Фаъолсозии дурдаст (REM): Сими фаъолсозии дурдастро аз баромади дурдасти дастгоҳи асосии худ ба терминали REM дар дастгоҳ пайваст кунед ampлифти барқ. Ин сим сигнал медиҳад ampлифт барои фаъол ва хомӯш кардани системаи аудиоии шумо.
2. Audio Input Connections:
Connect RCA cables from your head unit's pre-out (RCA output) to the RCA input jacks on the amplifier. Ensure correct left and right channel connections if applicable, though this is a mono ampлифер.
3. Speaker Output Connections:
Connect your subwoofer(s) or full-range speakers to the speaker output terminals on the amplifier. Pay close attention to polarity (+ and -) and ensure the total impedance of your speakers matches the amplifier's rated impedance (1 Ohm for this model). Refer to the specifications section for impedance details.
4. Монтаж:
Монтед amplifier securely in a location that provides adequate ventilation and protection from moisture. Avoid mounting it directly on carpet or in enclosed spaces without airflow.
Дастурҳои амалиётӣ
1. Initial Power-Up:
After all connections are made, reconnect the vehicle's battery. Turn on your head unit. The "POWER" indicator on the amplifier should illuminate, indicating it is receiving power and is operational.
2. Танзими фоида:
Назорати фоидаро дар amplifier барои мувофиқат бо ҳаҷми баромадtage of your head unit. Start with the gain at its minimum setting. Play a familiar track at about 75% of your head unit's maximum volume. Slowly increase the amplifier's gain until you hear distortion, then back it off slightly. The "CLIP" indicator should only flash briefly on very dynamic peaks, not stay illuminated.
3. Crossover Settings:
The Vulcan 9K EQ features adjustable crossovers:
- Филтри гузариш паст (LPF): Adjust this control to set the upper frequency limit for your subwoofers. Frequencies above this setting will be attenuated.
- Филтри гузариш баланд (HPF): Adjust this control to set the lower frequency limit for your speakers. Frequencies below this setting will be attenuated. This is typically used for full-range speakers or mid-bass drivers.
Refer to your speaker manufacturer's recommendations for optimal crossover points.
4. Equalizer Adjustment (3-Band EQ):
Дар amplifier includes a 3-band equalizer to fine-tune the audio output:
- Бас: Вокуниши басомади пастро танзим мекунад.
- Басси миёна: Adjusts the mid-low frequency response.
- Миёнаи баланд: Adjusts the mid-high frequency response.
Make small adjustments and listen carefully to achieve your desired sound balance. Avoid excessive boosting, which can lead to distortion or speaker damage.
Нигоҳдорӣ
- -ро нигоҳ доред ampлифт тоза ва аз чангу хошок тоза. Барои тоза кардан матои мулоим ва хушкро истифода баред.
- Дар атрофи ҳаво гардиши мувофиқро таъмин кунед amplifier at all times to prevent overheating. Regularly check that cooling fins are not obstructed.
- Periodically check all wiring connections for tightness and corrosion. Loose connections can cause performance issues or damage.
Дастур барои ҳалли мушкилот
| Мушкилот | Сабаби эҳтимолӣ | Ҳалли |
|---|---|---|
| Не қудрат / Ampлифт ба кор намеояд |
|
|
| Не баромади садо |
|
|
| Amplifier in Protection Mode (PROT light on) |
|
|
| Овози таҳрифшуда |
|
|
Мушаххасоти техникӣ
| Хусусият | Арзиш |
|---|---|
| RMS Power at 1 Ohm (12.6V) | 1 x 9,000 Вт RMS |
| RMS Power at 2 Ohm (12.6V) | 1 x 5,400 Вт RMS |
| RMS Power at 4 Ohm (12.6V) | 1 x 3,200 Вт RMS |
| RMS Power at 1 Ohm (13.8V) | 1 x 10,000 Вт RMS |
| RMS Power at 2 Ohm (13.8V) | 1 x 6,400 Вт RMS |
| RMS Power at 4 Ohm (13.8V) | 1 x 3,900 Вт RMS |
| Таҳвили ҷилдиtage | 9.5 ~ 15 В. |
| Ҷавоби басомад | 10 Гц ~ 15 КГц |
| Crossover Low Pass | 50 Гц ~ 15 КГц |
| Ағбаи баланди кроссовер | 10 Гц ~ 70 Гц |
| Сигнал ба таносуби садо | > 90 дБ |
| Harmonic Distortion (THD) | < 0.9 % |
| Ҳассосияти вуруд | 0.2В |
| Импеданси вуруд | 27К Ом |
| Импеданси баромад | 1 Ом |
| Consumption (Musical Signal) | 6.7A ~ 445A (12.6V) |
| Consumption (Bass Signal) | 6.7A ~ 890A (12.6V) |
| Андозаҳо (H x W x D) | 75.5 x 308 x 510 мм |
| Вазн | 7.4 кг |
Кафолат ва дастгирӣ
Stetsom products are manufactured to the highest quality standards. For specific warranty terms and conditions, please refer to the warranty card included with your product or visit the official Stetsom website. For technical support or service inquiries, please contact your authorized Stetsom dealer or Stetsom customer service.
Webсайт: www.stetsom.com.br (Хурampистинод, истиноди воқеӣ метавонад фарқ кунад)
