1. Муқаддима
This manual provides essential information for the proper installation, operation, and maintenance of your True Manufacturing GDM-49-HC~TSL01 Glass Door Merchandiser. Please read these instructions thoroughly before operating the unit to ensure safe and efficient performance. Retain this manual for future reference.
2. Маълумот оид ба бехатарӣ
ОГОҲ: Хавфи зарбаи барқ. Пеш аз хидматрасонӣ барқро ҷудо кунед.
- Боварӣ ҳосил кунед, ки дастгоҳ дуруст ба замин пайваст карда шудааст, то хатари барқро пешгирӣ кунад.
- Дар ин асбоб моддаҳои таркандаро, аз қабили банкаҳои аэрозолии дорои сӯзишвории оташгиранда нигоҳ надоред.
- Қуттиҳои вентилятсияро дар корпуси дастгоҳ ё сохтори дарунсохт аз монеа тоза нигоҳ доред.
- Барои суръат бахшидан ба раванди яхбандӣ, ғайр аз он чизе, ки истеҳсолкунанда тавсия додааст, аз дастгоҳҳои механикӣ ва дигар воситаҳо истифода набаред.
- Схемаи яхдонро вайрон накунед.
- Таъмирро танҳо кормандони соҳибихтисос бояд анҷом диҳанд.
3. Танзим ва насб
3.1 Кушодани баста
Carefully remove all packaging materials, including tape and protective film. Inspect the unit for any shipping damage. Report any damage immediately to the carrier and your dealer.
3.2 Ҷойгиркунӣ
Position the merchandiser on a strong, level surface capable of supporting its weight when fully loaded. Ensure adequate clearance around the unit for proper ventilation. Avoid direct sunlight or proximity to heat-generating equipment.
Расми 1: Пеш view of the True Manufacturing GDM-49-HC~TSL01 Glass Door Merchandiser.
3.3 Сатҳи
Use a level to ensure the unit is perfectly level. Adjust the leveling feet at the bottom of the unit as needed. Proper leveling is crucial for door alignment and efficient operation.
3.4 Пайвастшавӣ ба барқ
Connect the merchandiser to a dedicated, properly grounded electrical outlet. Refer to the unit's data plate for specific voltagд ва amperage requirements. Do not use extension cords.
3.5 Насб кардани раф
The unit comes with 8 adjustable wire shelves. Install them by inserting the shelf clips into the desired slots on the vertical pilasters inside the cabinet. Ensure all clips are securely seated and the shelves are level before loading products.
Figure 2: Technical drawing illustrating dimensions and features of the GDM-49-HC~TSL01.
4. Дастурҳои истифодабарӣ
4.1 Оғози ибтидоӣ
After connecting to power, allow the unit to run for several hours empty to reach its operating temperature before loading products. The factory-set temperature range is typically 33°F to 38°F (0.5°C to 3.3°C).
4.2 Назорати ҳарорат
The merchandiser features an electronic control system. Adjust the temperature settings using the digital display and buttons, typically located on the front or side of the unit. Refer to the control panel instructions for precise adjustments.
4.3 Боркунии маҳсулот
Load products evenly on the shelves, ensuring not to block the internal airflow or exceed the shelf weight capacity. Avoid placing items directly against the back wall to maintain proper air circulation.
4.4 Фаъолияти дар
The unit is equipped with self-closing glass doors. Ensure doors close completely after each use to maintain internal temperature and energy efficiency. The doors feature a positive seal torsion type closure system.
5. Нигоҳдорӣ
5.1 Тозакунии корҳои дохилӣ
Regularly clean the interior surfaces with a mild soap and water solution. Rinse thoroughly and dry with a clean cloth. Do not use abrasive cleaners or sharp objects that could damage the surfaces.
5.2 Тозакунии берун
Wipe down the exterior with a soft cloth and mild detergent. For stainless steel surfaces, use a non-abrasive cleaner designed for stainless steel, wiping in the direction of the grain.
5.3 Тоза кардани кати конденсатор
The condenser coil should be cleaned regularly (monthly or quarterly, depending on environment) to ensure optimal performance and energy efficiency. Disconnect power before cleaning. Use a stiff brush or vacuum cleaner to remove dust and debris from the coil. An easily accessible condenser coil is located at the bottom front of the unit.
5.4 Санҷиши прокладка
Periodically inspect the door gaskets for tears or damage. Ensure they form a tight seal when the doors are closed. Replace damaged gaskets promptly to prevent air leakage and maintain efficiency.
5.5 Барф кардани худкор
This unit features an automatic defrost system, eliminating the need for manual defrosting. Ensure the drain pan is clear and free of obstructions.
6. Баррасии мушкилот
Пеш аз тамос бо хидмат, дубораview масъалаҳои умумӣ ва роҳҳои ҳалли зерин:
| Мушкилот | Сабаби эҳтимолӣ | Ҳалли |
|---|---|---|
| Агрегат хунук намешавад | Power supply issue, thermostat setting, dirty condenser coil, blocked airflow | Check power connection, adjust thermostat, clean condenser, ensure proper loading. |
| Садои аз ҳад зиёд | Loose components, fan obstruction, unit not level | Қисмҳои фуҷурро тафтиш кунед, минтақаи вентиляторро тоза кунед, дастгоҳро ҳамвор кунед. |
| Дарҳо дуруст баста намешаванд | Obstructed hinges, damaged gaskets, unit not level | Clear obstructions, inspect/replace gaskets, level the unit. |
| Об дар ошёна | Clogged drain line, excessive humidity | Clear drain line, ensure doors are closed, check ambient humidity. |
Агар пас аз кӯшиши ин роҳҳои ҳалли мушкилот мушкилот боқӣ монад, бо мутахассиси хидматрасонии соҳибихтисос тамос гиред.
7. Мушаххасоти
The True Manufacturing GDM-49-HC~TSL01 is designed for commercial use, offering reliable refrigeration for various products.
| Хусусият | Тафсилот |
|---|---|
| Бренд | Дуруст |
| Маълумоти модели | GDM-49-HC~TSL01 |
| Вазни ашё | 630 фунт |
| Андозаҳои маҳсулот | 29.88 x 54.13 x 78.63 инч |
| Навъи насб | Озодагон |
| Формаи форма | Компакт |
| Имконоти ранг | Black Standard, Optional White, Optional Stainless |
| Racks / Shelves | 8 Рафҳои симӣ |
| Системаи об кардани ях | Автоматӣ |
| Халқаҳои дар | Бозгаштшаванда |
| Навъи маводи дари | Шиша |
| Сертификатсия | NSF |
| Шумораи дарҳо | 2 |
| яхдон | R-290 |
Figure 3: Detailed specifications and plan view diagrams for the GDM-49-HC~TSL01.
8. Кафолат ва дастгирӣ
True Manufacturing provides a comprehensive warranty for this product. For specific warranty terms and conditions, please refer to the warranty card included with your unit or visit the official True Manufacturing website. For technical support, parts, or service inquiries, please contact your authorized True dealer or True Manufacturing customer service directly. Ensure you have your model number (GDM-49-HC~TSL01) and serial number available when contacting support.
True Manufacturing Contact Information:
Webсайт: www.truemfg.com
Phone: Refer to your product documentation for regional contact numbers.
