Дастури истифодабарии Leviton DOS05-1LZ Decora барои гузариши чароғи сенсори ҳаракат

1. Муқаддима

The Leviton DOS05-1LZ Decora Motion Sensor Light Switch is designed to provide automatic lighting control based on occupancy and motion detection. This 180° Passive Infrared (PIR) sensor can operate in either single-pole or 3-way configurations and does not require a neutral wire for installation, making it suitable for a wide range of residential applications. It is compatible with various load types including LED, CFL, Incandescent, Halogen, Magnetic Low Voltagд, Electronic Low Voltage, and motor loads up to ¼ HP. This device helps enhance convenience and energy efficiency by automatically turning lights on when motion is detected and off after a set period of inactivity.

The switch includes interchangeable faceplates in White, Ivory, and Light Almond to match your decor. It can also be used to comply with 2019 California Title 24, Part 6 Vacancy Control Device Requirements.

2. Маълумот оид ба бехатарӣ

WARNING: To avoid fire, shock, or death, always turn off power at the circuit breaker or fuse and test to ensure power is off before wiring. If you are unsure about any part of these instructions or are not comfortable or familiar with electrical wiring, contact a licensed electrician.

• This device is designed for use with copper or copper-clad wire only.
• Do not mount near a heat source or in drafty areas of the home, as temperature changes can affect sensor performance.
• Avoid mounting in motion-heavy areas where unintended motion will be within the sensor's field of view, unless adjusted for specific coverage.

3. Мундариҷаи баста

• One Leviton DOS05-1LZ Motion Sensor Light Switch
• Interchangeable faceplates (White, Ivory, Light Almond)
• Дастурҳо оид ба насб

4. Насбкунӣ

4.1. Воситаҳои зарурӣ

• Отверткаи ҳамвор
• Филлипс-отвертка
• Electrician's pliers
• Стриптер
• Лентаи электрикӣ
• Handheld voltagсанҷанда
• Properly sized wire connectors

4.2. Қадамҳои пеш аз насб

1. Қувваи барқро дар ноқил ё сӯзишворӣ хомӯш кунед.
2. Remove the existing switch plate and unscrew the old device from the wall box.
3. Carefully pull the device out until you clearly see the wires.
4. Ҳаҷмро истифода баредtage tester to ensure no power is present in the box.
5. Carefully disconnect all wiring from the old device and remove it.
6. Straighten and separate each wire. Ensure no exposed metal ends are touching.

4.3. Wiring the Motion Sensor Switch

The DOS05-1LZ can be wired with or without a neutral wire. Identify the wires in your wall box to determine the appropriate wiring configuration.

Figure 1: Leviton DOS05-1LZ Motion Sensor Switch with pre-stripped wires.

Расми 2: Бозгашт view of the switch showing wiring terminals and labels.

4.3.1. Wiring without a Neutral Wire (Ground Connection)

• Twist the green and yellow ground lead wire from the device and the green sleeve ground wire (if present) to the ground wire in the wall box. Secure with a properly sized wire connector and electrical tape.
• Connect the black lead wires from the device to the black wires (line and load) in the wall box. The line and load wires can be wired interchangeably. Secure with wire connectors and electrical tape.
• For DOS05-1LZ, cap off the red/yellow wire with a wire connector as it is only used for 3-way connections.

4.3.2. Wiring with a Neutral Wire

• Remove the green sleeve from the white wire on the product. Connect this white wire to the white neutral wire(s) in the wall box. Secure with a properly sized wire connector and electrical tape.
• Connect the green and yellow ground lead wire from the device to the ground wire in the wall box. Secure with a properly sized wire connector and electrical tape.
• Connect the black lead wires from the device to the black wires (line and load) in the wall box. The line and load wires can be wired interchangeably. Secure with wire connectors and electrical tape.
• For DOS05-1LZ, cap off the red/yellow wire with a wire connector as it is only used for 3-way connections.

4.4. Қадамҳои ниҳоӣ

1. Gently bend the wires and push them into the wall box.
2. Screw the sensor into the wall box.
3. Install the wall plate (sold separately).
4. Қувваи барқро дар сими хомӯш ё сақф барқарор кунед.

5. Дастурҳои истифодабарӣ

5.1. Амалиёти асосӣ

• Худкор фурӯзон/хомӯш: After a warm-up period (10-20 seconds), the lights will automatically turn on with the first motion detected. They will turn off after a set period of inactivity.
• Дастӣ фурӯзон/хомӯш: Press the lower part of the push pad to manually turn the lights on or off.
• Motion Detected Indicator: The red indicator light will flash anytime motion is detected.
• Light Off Indicator: The green indicator light illuminates when the light (load) it controls is off.

5.2. Танзимоти барномарезишаванда

The DOS05-1LZ offers three programmable settings: Timer, Sensitivity, and Ambient Light. These settings can be adjusted directly from the push pad without tools or removing the faceplate.

Figure 3: Adjust settings by pressing the push pad, no tools required.

5.2.1. Ворид шудан ба режими барномасозӣ

1. Manually turn the light ON by pressing the push pad. The green LED will be off.
2. Press the TOP and BOTTOM of the push pad simultaneously for 5 seconds.
3. The green LED will turn on for 5 seconds, then the red LED will blink once, and the green LED will blink three times. This indicates you are in Programming Mode, currently in the Timer Setting (Option 3, 10 minutes, default).

Шарҳ: Programming Mode will time out after 30 seconds if no activity is detected, and changes will not be saved.

5.2.2. Changing Settings and Options

• To change the Setting (Timer, Sensitivity, Ambient Light): Press the TOP of the push pad. The red LED will blink to indicate the setting number (1 blink for Timer, 2 for Sensitivity, 3 for Ambient Light).
• To change the Setting Option (e.g., 1 minute, 5 minutes for Timer): Press the BOTTOM of the push pad. The green LED will blink to indicate the option number (1 blink for Option 1, 2 for Option 2, etc.).

5.2.3. Timer Setting (Setting 1)

Adjusts the duration the light remains ON after motion was last detected.

• Option 1: 1 Minute
• Option 2: 5 Minutes
• Option 3: 10 Minutes (Default)
• Option 4: 20 Minutes

5.2.4. Sensitivity Setting (Setting 2)

Adjusts the device's sensitivity to motion, affecting the detection range.

• Option 1: Low (50% range)
• Option 2: Medium (Default)
• Option 3: High (Maximum coverage area)

Figure 4: 180° PIR detection range, up to 900 sq. ft. Customize sensing range/coverage area for your application.

5.2.5. Ambient Light Setting (Setting 3 - Occupancy Sensors Only)

Adjusts the device's sensitivity to natural light, preventing lights from turning on if there is ample natural light in the room.

• Option 1: Low Light Level
• Option 2: Medium Light Level (Default)
• Option 3: High/Brightest Light Level
• Option 4: Disabled (Light turns on for all light levels regardless of ambient light)

5.3. Temporary Modes

5.3.1. Усули санҷиш

Turns on the light for 5 seconds every time motion is detected. Useful for testing field of view coverage after installation.

• Барои фаъол кардан: Press and hold the TOP of the push pad for 5 seconds. The red light will blink once every 2 seconds.
• Барои баромадан: Press the TOP or BOTTOM of the push pad, or it will automatically time out after 2 minutes.

5.3.2. Temporary Bypass Mode (Occupancy Sensors Only)

Ignores motion, preventing detection and keeping the light or load off. Useful when you want a room to remain dark even if there is motion (e.g., watching a movie).

• Барои фаъолсозӣ: Press and hold the BOTTOM of the push pad for 5 seconds. The green light will double flash every 2 seconds.
• Барои баромадан: Press the TOP or BOTTOM of the push pad.

6. Баррасии мушкилот

7. Мушаххасоти

• Рақами модел: DOS05-1LZ
• Реҷаи кор: ДАРОМАД-ХОМУШ-ФУРОИШ
• Рейтинги ҷорӣ: 2 Amps
• Ҷилди амалиётӣtage: 120 вольт
• Навъи тамос: Одатан кушода
• Навъи пайвасткунанда: Кримп
• Терминал: Майса
• Андозаҳои ашё (L x W x H): 1.38 x 1.73 x 4.13 инч
• Навъи схема: 3-роҳ
• Навъи фаъолкунанда: Тугмаи пахш кунед
• Мавод барои тамос: Фосфори биринҷӣ
• Рейтинги байналмилалии муҳофизат: IP54
• Шумораи мавқеъҳо: 1
• Рейтинги ҳарорати паст: 70 дараҷа Фаренгейт
• Рейтинги ҳарорати боло: 100 дараҷа Фаренгейт
• Навъи нозир: Тугмаи пахш кунед
• Усули назорат: ламс кунед
• Протоколи пайвастшавӣ: X-10
• Ранги: White/Ivory/Light Almond
• Ватtage: 600 ватт
• Дастгоҳҳои мувофиқ: LED, CFL, Incandescent, Halogen, Magnetic Low Voltagд, Electronic Low Voltage, Motor loads
• Манбаи нерӯ: Электри симдор
• Вазни ашё: 4.6 унция

8. Нигоҳдорӣ

To maintain optimal performance and appearance of your Leviton Motion Sensor Light Switch, follow these simple guidelines:

• Тозакунӣ: нармро истифода баред, гamp cloth to clean the surface of the switch. Avoid abrasive cleaners, solvents, or harsh chemicals, as these can damage the finish or internal components.
• Санҷиш: Ба таври даврӣ гузаришро аз рӯи аломатҳои вайроншавӣ, пайвастҳои суст ё кори ғайриоддӣ тафтиш кунед. Агар ягон мушкилот мушоҳида шавад, барқро дар автомати автоматӣ хомӯш кунед ва ба электрики соҳибихтисос муроҷиат кунед.
• Нигоҳубини линза: Keep the sensor lens clean and free from dust or obstructions to ensure accurate motion detection.
• Мулоҳизаҳои экологӣ: Ensure the switch is not exposed to excessive moisture or extreme temperatures beyond its operating range, as this can affect its lifespan and functionality.

9. Кафолат ва дастгирӣ

This Leviton Motion Sensor Light Switch (DOS05-1LZ) comes with a Кафолати маҳдуди 5-сола. For warranty claims, technical support, or further assistance, please contact Leviton customer service or visit their official webсайт. Ҳуҷҷати хариди худро барои тасдиқи кафолат нигоҳ доред.