Дастури истифодабарии Thermalright Frozen Notte 360 ​​White ARGB V2 CPU Move Cover

1. Муқаддима

The Thermalright Frozen Notte 360 White ARGB V2 is an all-in-one (AIO) liquid CPU cooler designed to provide efficient thermal management for your processor. It features a 360mm radiator, three 120mm PWM ARGB fans, and a high-performance water block with an integrated pump. This manual provides detailed instructions for installation, operation, and maintenance to ensure optimal performance and longevity of your cooler.

Image 1.1: Thermalright Frozen Notte 360 White ARGB V2 CPU Liquid Cooler with RGB fans and pump.

2. Мундариҷаи баста

Лутфан тафтиш кунед, ки ҳамаи ҷузъҳо пеш аз оғози насб мавҷуд аст:

• 1x Thermalright Frozen Notte 360 White ARGB V2 AIO Cooler (Radiator, Pump/Water Block, Tubing)
• 3x TL-E12W-S V2 120mm PWM ARGB Fans
• Intel Mounting Hardware (Backplate, Standoffs, Screws)
• AMD Mounting Hardware (Brackets, Screws)
• Омехтаи гармӣ
• Fan PWM Splitter Cable
• Сими тақсимкунандаи ARGB
• Дастури корбар

Тасвири 2.1: Ба охир расидview of the Thermalright Frozen Notte 360 White ARGB V2 and included accessories.

3. Мушаххасоти

4. Мутобиқат

The Thermalright Frozen Notte 360 White ARGB V2 CPU Liquid Cooler supports a wide range of CPU sockets:

• Intel: LGA 1150, 1151, 1155, 1156, 1200, 1700, 1851, 2011, 2066
• AMD: AM4, AM5, AM2, AM2+, AM3, AM3+, FM1, FM2, FM2+

For optimal installation, a chassis width greater than 250mm is recommended.

5. Танзим ва насб

This section provides general installation steps. Refer to the official installation video for a visual guide.

5.1. Омодагии умумӣ

• Ensure your motherboard is removed from the PC case or has sufficient access to the CPU socket area.
• Remove any existing CPU cooler and clean the CPU surface thoroughly with isopropyl alcohol.
• Identify the correct mounting hardware for your CPU socket (Intel or AMD).

5.2. Intel LGA1700 Installation

1. Adjust the backplate: For LGA1700, use the outer holes on the universal backplate.
2. Install the Intel backplate: Position the backplate on the rear side of your motherboard, aligning the holes with the CPU socket.
3. Install 1700 standoffs: From the front side of the motherboard, screw in the blue-colored LGA1700 standoffs onto the backplate screws.
4. Apply thermal compound: Apply a small amount of the provided thermal compound onto the center of the CPU's Integrated Heat Spreader (IHS).
5. Prepare the water block: Align the arrow on the Intel mounting bracket with the corresponding mark on the water block, then rotate to lock it in place.
6. Remove protective sticker: Peel off the protective sticker from the copper cold plate of the water block.
7. Install the water block: Carefully place the water block onto the CPU, aligning the mounting holes on the bracket with the standoffs.
8. Secure the water block: Use the four provided nuts to secure the metal brackets and water block to the standoffs. Tighten them in a diagonal pattern until snug, ensuring even pressure.

5.3. Насби AMD AM5/AM4

1. Prepare the water block: Rotate to install the AMD mounting bracket onto the water block.
2. Apply thermal compound: Apply a small amount of the provided thermal compound onto the center of the CPU's Integrated Heat Spreader (IHS).
3. Remove protective sticker: Peel off the protective sticker from the copper cold plate of the water block.
4. Install the water block: Use the buckles on the AMD bracket to secure the water block onto the CPU.
5. Tighten screws: Tighten both screws on the bracket with a screwdriver to apply mounting pressure.

5.4. Fan and Cable Connections

• Mount fans: Attach the three 120mm fans to the radiator using the provided screws. Ensure the fan direction is set for optimal airflow (typically intake or exhaust depending on your case configuration).
• Connect fan ARGB: Connect the 3-pin ARGB cables from each fan to the included ARGB splitter cable.
• Connect fan PWM: Connect the 4-pin PWM headers from each fan to the included PWM splitter cable.
• Connect fan splitter to motherboard: Plug the PWM splitter cable into the CPU_FAN header on your motherboard.
• Connect pump power: Connect the pump's 3-pin power cable to a dedicated pump header on your motherboard (e.g., CPU_OPT, AIO_PUMP, or WATER_PUMP).
• Connect ARGB lighting: Connect the ARGB splitter cable to a 3-pin +5V ARGB header on your motherboard for lighting control.

Image 5.2: Close-up of the water block with its mirror plating and ARGB lighting.

Image 5.3: Details of the TL-E12W-S V2 fans, highlighting S-FDB bearing and PWM control.

6. Дастурҳои истифодабарӣ

Once installed, the Thermalright Frozen Notte 360 White ARGB V2 operates automatically based on your motherboard's settings:

• Идоракунии вентиляторҳои PWM: The 4-pin PWM fans will automatically adjust their speed based on the CPU temperature, providing optimal cooling performance while minimizing noise. You can configure fan curves in your motherboard's BIOS/UEFI settings or through compatible software.
• Ҳамоҳангсозии равшании ARGB: The ARGB lighting on the fans and water block can be synchronized with your motherboard's 5V 3-pin ARGB header. Use your motherboard's RGB control software (e.g., ASUS Aura Sync, MSI Mystic Light, Gigabyte RGB Fusion, ASRock Polychrome Sync) to customize lighting effects and colors.
• Фаъолияти насос: The pump operates continuously to circulate coolant. Ensure the pump header in your BIOS is set to full speed or a constant voltage to maintain consistent flow.

7. Нигоҳдорӣ

Regular maintenance helps ensure the longevity and performance of your liquid cooler:

• Тоза кардани хок: Periodically clean dust from the radiator fins and fan blades using compressed air. Accumulated dust can impede airflow and reduce cooling efficiency.
• Санҷиши қубур: Occasionally check the high polymer woven protective water pipes for any signs of wear, kinks, or leaks.
• Хамираи гармидиҳӣ: While not frequently required, if you ever remove the water block from the CPU, you must clean off the old thermal paste and apply a fresh layer before reinstallation.
• Сатҳи моеъи хунуккунӣ: As a closed-loop system, the AIO cooler does not typically require coolant refills. However, if you notice unusual performance or noise, consult Thermalright support.

8. Баррасии мушкилот

If you encounter issues with your Thermalright Frozen Notte 360 White ARGB V2, consider the following:

• Қувва нест/Вентиляторҳо чарх намезананд:
  • Check all power connections (PWM splitter to CPU_FAN, pump power to AIO_PUMP/CPU_OPT).
  • Ensure the motherboard headers are enabled and configured correctly in BIOS.
• Ҳарорати баланди CPU:
  • Verify the water block is securely mounted to the CPU with adequate pressure.
  • Confirm thermal compound was applied correctly and evenly.
  • Check fan orientation and ensure they are pushing/pulling air through the radiator effectively.
  • Ҳама гуна ғуборро аз қуттиҳои радиатор тоза кунед.
  • Ensure pump is running at full speed (check BIOS settings).
• ARGB Lighting Not Working/Incorrect Colors:
  • Ensure the 3-pin +5V ARGB cable is correctly connected to the motherboard header.
  • Verify your motherboard's RGB software is installed and configured.
  • Check for loose connections in the ARGB splitter cable.
• Unusual Noise (Gurgling/Whining):
  • AIO coolers can sometimes have air bubbles. Gently tilt your PC case to help move air bubbles to the radiator.
  • Ensure the pump is not the highest point in the loop to prevent air from accumulating in the pump.

9. Кафолат ва дастгирӣ

Thermalright products are designed for durability and performance. For specific warranty details and terms, please refer to the official Thermalright webсайт ё бевосита бо дастгирии мизоҷони худ тамос гиред. Барои даъвоҳои кафолат далели хариди худро нигоҳ доред.

For technical assistance, troubleshooting, or further inquiries, please visit the Thermalright support page or contact their customer service team.