1. Муқаддима
This manual provides detailed instructions for the installation, operation, and maintenance of your Stinger Audio MT-1000.1M 1-Channel Monoblock Marine Audio Subwoofer Amplifier. Please read this manual thoroughly before attempting installation or operation to ensure proper use and to prevent damage to the unit or your audio system. Keep this manual for future reference.
2. Маҳсулот ба охир расидview
The Stinger Audio MT-1000.1M is a high-efficiency Class-D monoblock amplifier designed for marine environments. It delivers 1000 Watts RMS of power, optimized for subwoofer applications. Its robust, water-resistant design ensures reliable performance in challenging conditions.
Хусусиятҳои асосӣ:
- Digital Class-D Monoblock Ampумр: High efficiency and compact form factor.
- Тарҳрезии паймон ва устувор: Built for lasting reliability.
- Манбаъҳои қувваи устувори танзимнашаванда: Designed for superior performance and efficiency.
- Мукаммали HEXFET Power MOSFET: Features reduced on-resistance, faster switching speeds, and enhanced reliability.
- Терминалҳои мустақими воридкунии барқ ва баландгӯяк: Муқовимати паст барои интиқоли нерӯи барқ ва самаранокии баландтар.
- Тарҳрезии ба об тобовар: Муҳофизат мекунад amplifier against weather elements for uninterrupted performance.
- Bass Boost Q: Adjustable bass boost from 0dB to 12dB at a selected frequency.
- Remote Bass Knob Included: Flush-mount design for effortless bass level adjustment.
3. Маълумот оид ба бехатарӣ
Ҳамеша чораҳои бехатарии зеринро риоя кунед:
- Disconnect the vehicle's negative battery terminal before any installation.
- Ба заминкании дурусти шасси мошинро таъмин кунед.
- Барои пайвастҳои барқ, замин ва баландгӯяк аз симҳои мувофиқи ченак истифода баред.
- насб кунед amplifier in a well-ventilated area, away from direct heat sources.
- Аз насб кардан худдорӣ намоед amplifier in locations where it may be submerged in water, despite its water-resistant rating.
- Агар шумо дар бораи ягон қисми раванди насб боварӣ надошта бошед, ба як насбкунандаи касбӣ муроҷиат кунед.
4. Дар қуттӣ чӣ мавҷуд аст
Пеш аз оғози насбкунӣ тасдиқ кунед, ки ҳама ҷузъҳо мавҷуданд:
- 1000 ватт моноблок Amplifier (MT-1000.1M)
- Remote Level Control (Bass Knob)
- Таҷҳизоти васлкунӣ
- Дастури дастурӣ
5. Муайянкунии ҷузъҳо
Бо худ шинос шавед amplifier's controls and connections.
5.1 Control Panel (Input Side)
- POWER/PRT/CLIP Indicators: LEDs indicating power status, protection mode, and signal clipping.
- REMOTE Port: RJ11 connection for the included remote bass level control.
- Вуруд (RCA): Audio input from your head unit or source.
- BRIDGE IN/OUT (RCA): For linking multiple ampосебдидагон.
- Назорати GAIN: Adjusts the input sensitivity to match the output of your source unit.
- LPF (Low-Pass Filter) Control: Adjusts the upper frequency limit for the subwoofer. Range: 40Hz - 180Hz.
- SUBSONIC Filter: Removes ultra-low frequencies below the audible range to protect the subwoofer. Range: OFF - 50Hz.
- FREQ (Bass Boost Frequency) Control: Selects the center frequency for the bass boost. Range: 30Hz - 80Hz.
- BOOST (Bass Boost Level) Control: Adjusts the level of bass boost. Range: 0dB - 12dB.
5.2 Terminal Panel (Output Side)
- GND (Ground) Terminal: Connects to the vehicle's chassis ground.
- REM (Remote) Terminal: Connects to the remote turn-on lead from your source unit.
- +12V (Power) Terminal: Connects to the positive terminal of the vehicle's battery via an inline fuse.
- MONO OUTPUT (Speaker Terminals): Connects to your subwoofer(s). Minimum impedance 1 Ohm.
6. Насбкунӣ
Proper installation is crucial for optimal performance and safety. Ensure all connections are secure and correctly polarized.
6.1 Ҷойгиршавӣ
Choose a mounting location that is secure, provides adequate ventilation, and is protected from excessive moisture. While the amplifier is water-resistant, direct exposure to heavy water spray or submersion should be avoided.
6.2 Пайвастҳои ноқилӣ
- Қувваи (B+): Connect a 4-gauge power cable from the +12V terminal of the amplifier directly to the positive terminal of the vehicle's battery. Install an appropriate inline fuse (100A recommended) within 18 inches of the battery.
- Замин (GND): Connect a 4-gauge ground cable from the GND terminal of the amplifier to a clean, bare metal point on the vehicle's chassis. Ensure a solid, low-resistance connection.
- дурдаст (REM): Connect a 18-gauge remote turn-on wire from the REM terminal of the amplifier to the remote output of your head unit.
- Вуруди RCA: Connect RCA cables from the subwoofer output of your head unit to the INPUT RCA jacks on the ampлифер.
- Натиҷаи баландгӯяк: Connect your subwoofer(s) to the MONO OUTPUT terminals. Ensure the total impedance is not below 1 Ohm. Observe correct polarity (+ to + and - to -).
- Тугмаи бассҳои дурдаст: Connect the remote bass knob to the REMOTE port on the ampлифт бо истифода аз сими додашуда.
7. Амалиёт
After installation, follow these steps to configure and operate your ampлифер.
7.1 Initial Setup and Gain Adjustment
- Turn the GAIN control on the amplifier to its minimum (counter-clockwise) position.
- Set your head unit's volume to about 75% of its maximum level.
- Як мусиқии динамикиро бо мундариҷаи қавии басс навозед.
- Slowly increase the GAIN control on the amplifier until you hear distortion, then back it off slightly until the sound is clear. The CLIP indicator should not illuminate continuously.
7.2 Crossover and Filter Settings
- LPF (Филтри пастгузар): Adjust the LPF control to set the upper frequency limit for your subwoofer. A common starting point is 80Hz-100Hz, but this may vary depending on your subwoofer and other speakers in your system.
- SUBSONIC Filter: Set the SUBSONIC filter to protect your subwoofer from playing frequencies below its resonant frequency. A common setting is 25Hz-30Hz, or slightly below your subwoofer's tuning frequency if it's in a ported enclosure. If you have a sealed enclosure, you may set it to OFF or a very low frequency.
7.3 Баланд бардоштани басс
- FREQ (Bass Boost Frequency): Select the frequency at which you want the bass boost to be centered. This is typically between 30Hz and 80Hz, depending on the desired effect.
- BOOST (Bass Boost Level): Adjust the level of boost from 0dB to 12dB. Use this sparingly to avoid distortion and potential damage to your subwoofer.
7.4 Тугмаи бассҳои дурдаст
The remote bass knob allows for convenient adjustment of the subwoofer output level from your listening position. It acts as a master volume for the subwoofer channel, allowing you to increase or decrease the bass intensity without affecting other ampтанзимоти лифт.
8. Нигоҳдорӣ
Нигоҳубини мунтазам ба таъмини давомнокӣ ва самаранокии кори дастгоҳи шумо мусоидат мекунад ampлифер.
- Тозакунӣ: Давра ба давра тоза кунед ampберунии lifier бо матои мулоим ва хушк. Аз истифодаи кимиёвии сахт ё тозакунандаи абразив худдорӣ намоед.
- Санҷиши пайвастшавӣ: Annually inspect all power, ground, remote, and speaker connections for corrosion or looseness. Tighten as necessary.
- Вентилятсия: Боварӣ ҳосил кунед, ки ampПарҳои хунуккунандаи лифтер аз монеаҳо холӣ мебошанд, то паҳншавии дурусти гармиро таъмин кунанд.
9. Баррасии мушкилот
Агар шумо бо мушкилоти худ дучор шавед amplifier, refer to the following common problems and solutions.
| Мушкилот | Сабаби эҳтимолӣ | Ҳалли |
|---|---|---|
| Не барқ / барқ LED хомӯш | Blown fuse, loose power/ground/remote wire, no remote signal. | Check inline fuse, verify all power connections, ensure head unit remote output is active. |
| LED-и муҳофизатӣ фурӯзон аст | Speaker short circuit, impedance too low, overheating, DC offset. | Check speaker wiring for shorts, verify speaker impedance, ensure adequate ventilation, disconnect speakers and test. |
| Не баромади аудио | No input signal, incorrect gain setting, speaker wires disconnected. | Check RCA connections, adjust gain, verify speaker connections. |
| Овози таҳрифшуда | Gain set too high, improper crossover settings, poor ground connection. | Reduce gain, adjust LPF/Subsonic filters, check ground wire for secure connection. |
10. Мушаххасоти
Detailed technical specifications for the Stinger Audio MT-1000.1M ampлифер.
| Хусусият | Мушаххасоти |
|---|---|
| Қувваи RMS (1Ω) | 1000W x 1 |
| Қувваи RMS (2Ω) | 650W x 1 |
| Қувваи RMS (4Ω) | 300W x 1 |
| Bridged RMS Rating (2Ω Minimum) | 1700W x 1 |
| Signal to Noise (CEA Standard) | -93дБ |
| Ҳассосияти вуруд | 0.5В - 11В |
| Фоида | 0.5В - 11В |
| Crossover Control (Linkwitz-Riley) | SUB 0Hz - 50Hz (Subsonic), LP 40Hz - 180Hz @ 12dB/Oct |
| Диапазони басомади баланд бардоштани басс | 30Гц - 80Гц |
| Bass-Boost Q | 0 - 12 дБ |
| Ҷавоби басомад (+/- 1dB) | 10Гц - 180Гц |
| Самаранокӣ (миёна) | 82% |
| Синфи топология | Синфи D |
| Назорати дурдасти басс | Ҳа (Дохил) |
| Ҷилди амалиётӣtage | 9V то 16V |
| Терминали барқ | 4 Ҳаҷ |
| Терминали баландгӯяк | 8 Ҳаҷ |
| Омезиши беруна тавсия дода мешавад | 100А |
| Вазни ашё | 6.14 фунт |
| Андозаҳои бастаҳо | 14.5 x 7.8 x 3.2 инч |
| Санаи аввалин дастрас | 13 марти соли 2024 |
| Истеҳсолкунанда | СТИНГЕР |
11. Кафолат ва дастгирӣ
11.1 Маълумот дар бораи кафолат
The Stinger Audio MT-1000.1M ampлифофа бо а меояд Кафолати 1 сол from the date of purchase. Please retain your proof of purchase for warranty claims. The warranty covers manufacturing defects and workmanship under normal use. It does not cover damage caused by improper installation, accident, misuse, abuse, neglect, or unauthorized modification.
11.2 Дастгирии муштариён
For technical assistance, troubleshooting, or warranty inquiries, please contact Stinger Audio customer support. You can find more information and contact details by visiting the official STINGER brand store:
