GODIYMODULES MAX98357A I2S 3W Class D Amplifier Breakout Module User Manual

1. Муқаддима

The GODIYMODULES MAX98357A I2S Class D Amplifier Breakout Module is designed to convert standard I2S digital audio input into an amplified analog signal, directly driving a speaker. This module integrates both a Digital-to-Analog Converter (DAC) and an amplifier into a single compact unit, making it suitable for projects requiring amplified sound output from I2S-compatible microcontrollers and microcomputers.

It is compatible with various platforms, including Raspberry Pi, Arduino Zero, and ESP32, offering a straightforward solution for audio output in embedded systems.

2. Хусусиятҳо

• Integrated I2S DAC and Class D Amplifier for direct speaker drive.
• Operates from a wide voltage range of 2.7V to 5.5V DC, ideal for portable applications.
• Built-in thermal and over-current protection for enhanced reliability.
• Supports I2S standard digital audio input with 3.3V or 5V logic data.
• Bridge-Tied Load (BTL) output configuration for direct speaker connection.
• Adjustable gain settings: 3dB, 6dB, 9dB (default), 12dB, or 15dB via the GAIN pin.
• Shutdown/Mode pin for chip shutdown and I2S audio channel selection (Left, Right, or (L+R)/2 mono mix).
• Compatible with Raspberry Pi, Arduino Zero, ESP32, and other microcontrollers with I2S audio outputs.

3. Мушаххасоти

4. Танзимот ва Пайвастшавӣ

This section details the pinout and connection procedures for integrating the MAX98357A amplifier module into your project.

4.1 Модул ба охир расидview

The module comes with pin headers for digital connections and screw terminals for speaker output. Ensure proper soldering of the pin headers if they are not pre-attached.

4.2 Pinout Description

Refer to the following table for a detailed description of each pin:

4.3 Дастурҳо оид ба васлкунӣ

1. Пайвасти барқ: Connect the VCC pin to your power supply (2.7V-5.5V DC) and GND to the system ground.
2. I2S Audio Input:
   • Connect DIN to the I2S Data Out pin of your microcontroller (e.g., Raspberry Pi, ESP32).
   • Connect BCLK to the I2S Bit Clock pin.
   • Connect LRC to the I2S Left/Right Clock (Word Select) pin.
3. Натиҷаи баландгӯяк: Connect your 4-8Ω speaker directly to the two speaker output terminals (labeled with '+' and '-' or simply the screw terminals). The outputs are "Bridge Tied" and should not be connected to ground or another ampлифер.
4. Gain Setting (Optional): The default gain is 9dB. To change the gain, manipulate the GAIN pin:
   • Connect GAIN to GND for 3dB.
   • Connect GAIN to VCC for 15dB.
   • Other gain settings (6dB, 12dB) can be achieved by connecting specific pull-up or pull-down resistors. Refer to the MAX98357 datasheet for exact resistor values.
5. Shutdown/Mode Control (Optional):
   • Pull the SD pin low to put the amplifier into shutdown mode, conserving power.
   • Бо нобаёнӣ, amplifier outputs an (L+R)/2 stereo mix into mono. By adding a resistor to the SD pin, you can configure it to output only the left or right channel. Refer to the MAX98357 datasheet for resistor configurations.

5. Амалиёт

Once the MAX98357A module is correctly wired to your microcontroller and speaker, its operation is primarily controlled by the I2S audio data stream and the configuration of the GAIN and SD pins.

1. Фаъол: Apply power within the 2.7V-5.5V DC range to the VCC and GND pins. The amplifier will initialize.
2. Бозии аудио: Begin sending I2S digital audio data from your microcontroller to the DIN, BCLK, and LRC pins. The module will automatically decode and amplify the audio, outputting it to the connected speaker.
3. Назорати овоз: The overall volume can be adjusted by changing the digital audio signal level from your microcontroller or by modifying the hardware gain setting via the GAIN pin as described in Section 4.3.
4. Пӯшида шудан: To conserve power, pull the SD pin low. This will put the amplifier into a low-power shutdown state. To resume operation, release the SD pin (allow it to float or pull it high, depending on your configuration).

For stereo output, two MAX98357A modules can be used, with one configured for the left channel and the other for the right channel via the SD pin, and both receiving the same BCLK and LRC signals but different DIN signals (left data for one, right data for the other).

6. Нигоҳдорӣ

The MAX98357A I2S Class D Amplifier Breakout Module is a robust electronic component designed for long-term operation with minimal maintenance.

• Тозакунӣ: If necessary, gently clean the module with a dry, soft brush or compressed air to remove dust. Avoid using liquids or solvents.
• Шароити экологӣ: Operate the module within typical indoor environmental conditions. Avoid exposure to extreme temperatures, high humidity, or corrosive environments.
• Санҷиши ҷисмонӣ: Periodically inspect connections for any signs of corrosion or loose wiring, especially for speaker terminals in high-vibration environments.

No user-serviceable parts are present on the module. Any repairs should be performed by qualified personnel.

7. Баррасии мушкилот

8. Кафолат ва дастгирӣ

Information regarding product warranty and customer support for the GODIYMODULES MAX98357A I2S 3W Class D Amplifier Breakout Module was not provided in the available product data. Please refer to the retailer or manufacturer's website for specific warranty terms and support contact information.