devolo Multi Node LAN 4TE
Мушаххасоти маҳсулот
- Нусхаи нармафзор: 7.16.5 ё навтар
- Истеҳсолкунанда: Деволо
- Тамос бо дастгирӣ: support@devolo.de
Маълумот оид ба маҳсулот
MultiNode is a networking device that allows you to create a MultiNode network for seamless connectivity.
Дастурҳои истифодаи маҳсулот
Насбкунӣ:
Install and configure your MultiNode network following these steps:
- Ensure your devices have firmware version 7.16.5 or newer.
- Decide whether to provision the devices before or after electrical installation.
- Run the setup wizard to begin the installation process.
Конфигуратсия:
After installation, you can configure your MultiNode network settings using the setup wizard or the user manual available on the product webсайт.
Муайян кардани мушкилот ва дастгирӣ:
If you encounter any issues or have feedback, please contact support at support@devolo.de барои ёрй.
This quick start guide helps you install and configure your first MultiNode network.
ℹ This guide assumes that your devices have firmware version 7.16.5 or newer. If your devices run an older firmware version, consult the user manual available on the маҳсулот webсайт.
Чӣ ба шумо лозим аст
- A laptop with a LAN port
- Сими Ethernet
- MultiNode LAN devices (at least two)
- Data sheet (technical specs, included in the package)
How MultiNode works
- MultiNode LAN 4TE is a DIN-rail device that uses powerline communication (PLC) to send data over low-voltagд.
- Master node: The central controller of the network.
- Regular nodes: They connect to the master through PLC. A regular node can automatically switch to a repeater role if needed.
- Ҷудогона будан: Regular nodes talk only to the master, not to each other.
Application devices (e.g., a charging station) connected to a regular node can only reach application devices connected to the master. Devices on different regular nodes cannot connect directly. - The master node has a built-in web interface for setup and management; no extra tools are needed.
Дастурҳои қадам ба қадам
- Шабакаи худро ба нақша гиред
- Power supply considerations: Each power rail needs a circuit breaker. You can use one breaker for both the charging station and MultiNode, or separate breakers. MultiNode is powered by L1/N, e.g., from the charging infrastructure’s mains circuit.
- Масофа: Large networks may need repeaters. The best range is up to 50 m per hop. 50–100 m may work, but over 100 m is not recommended.
- Схемаҳо: One three-phase circuit for all devices gives the best results. Multiple circuits cause signal loss and noise. This can be solved with repeaters or by splitting networks via Ethernet.
- Топология: The network self-organizes into a tree: the master node is at the root, with regular nodes automatically acting as repeaters when needed.
- Master node placement: Place it where Ethernet is easy to reach, and signal paths are short. It is strongly recommended not to place it in the distribution unit.
- Load management in EV charging scenarios: Since regular nodes connect only to the master, EV charging scenarios need careful upfront planning. For guidance, see the user manual on the маҳсулот webсайт.
- Монтажи электрик
- DIN-rail mounting and proper wiring must be carried out by a qualified electrician, in compliance with standards.
- Connect the MultiNode devices to the mains.
- It is recommended to record each device’s serial number, MAC address, and installation location (e.g., parking spot, floor number) to support maintenance.
You can provision the devices either before or after electrical installation, depending on what works best for your workflow.
- Connect your laptop
Connect your laptop to the device you want to use as the master node, e.g., the device next to the Internet gateway, with an Ethernet cable. By default, all MultiNode LAN 4TE devices start as regular nodes. - -ро кушоед web интерфейс.
- Кушодани а web браузер ва ворид кунед: http://devolo-xxxxx.local.
- Replace xxxxx with the last 5 digits of the device’s serial number.
- Устоди танзимотро иҷро кунед.
Вақте ки шумо кушодани web interface of a factory-default device, it automatically redirects you to the setup wizard.
- Click the button “Create a new network”. This sets the connected device as the master.
- On the above screen, wait for all nodes to join the network, then click “Continue. On the next screen shown below, enter the settings and click “Save and apply to all nodes in the network”:
- Номи домени Powerline: Choose a clear name for the MultiNode network to help identify it.
- Powerline password: Protects the powerline domain.
- Тухми: A number from 0 to 59 that uniquely identifies a PLC network. It is recommended to leave this on automatic.
- Рамзи администратор: Protects the MultiNode network management channel.
- Web interface password: Protects access to the web интерфейс.
- After the configuration is applied to all nodes, you will be automatically redirected to the Overview, which lists all nodes in your MultiNode network as shown below. It is recommended to provide meaningful names to nodes, e.g., include a referencethe physicalical installation location.
- Click the button “Create a new network”. This sets the connected device as the master.
Дастгирӣ
For questions or feedback, please contact us at support@devolo.de.
Саволҳои зиёд такрормешуда
Can I use MultiNode with older firmware versions?
MultiNode is designed to work best with firmware version 7.16.5 or newer for optimal performance and compatibility.
Do I need to configure each device individually in the network?
No, you can use the setup wizard to configure multiple devices simultaneously for easier network setup.
Ҳуҷҷатҳо / Сарчашмаҳо
 |
devolo Multi Node LAN 4TE [pdf] Дастури корбар 20251021, Multi Node LAN 4TE, Node LAN 4TE, LAN 4TE |